If you want to complete an FBA on the Smooth Front Plains Dress, then you can simply follow the instructions for Full Bust Adjustment (FBA) for a Top with a Bust Dart - Scenic, Vista.
For a SBA (Smaller Bust Adjustment) for the Curved Front Plains Dress, please see the following tutorial: Smaller Bust Adjustment (SBA) for the Curved Front Plains Dress.
Materials
Gather some basic materials to adjust the pattern pieces:- Upper Front & Lower Front pattern pieces from the Plains Dress
- measuring tape
- scrap paper
- tape
- ruler
- pen/pencil
- scissors
Measure
To determine the size of adjustment necessary, measure your high bust and full bust.
The high bust measurement is taken around the body, with the tape snugged up to the underarms, and above the breasts.
The bust measurement is taken around the fullest part of the breasts.
Compare your body measurements to the size chart in the pattern tutorial.
| Size H | Your body measurement | |
| High Bust measurement | 34" (86cm) | 34" (86cm) |
| Full Bust measurement | 36" (91cm) | 38" (96cm) |
BUST APEX
The dart is intended to “point” to the fullest part of the bust or the bust apex when the dress is worn.
The bust apex is marked on the pattern. It is a good idea to measure your own bust apex to make sure the bust dart ends up in the correct position for your body.
To find your personal bust apex, measure from the outside corner of the body on the shoulder bone (the position where a shoulder seam line would sit) to the centre of your bust - this is the part that points out the most. Note that the bust apex is not necessarily the same as your nipple position. We recommend taking this measurement while wearing your favourite underwear.
When taking a comparison measurement on the pattern it is taken from the stitching line on the outside corner of the shoulder seam to the bust apex point marked on the pattern.
Check your measurement against the pattern.
Keep a note of the difference between your bust position versus the pattern. For example:
| Pattern | = 9.8" (25cm) |
| Your Bust Position | = 11.8" (30cm) |
| Difference | = 2" (5cm) |
Fuller Bust Adjustment
ADJUST PATTERN PIECES
1. Begin by drawing cut lines on the Front pattern piece:
a. Line parallel to Centre Front (CF) from the hem of Lower Front to the top curve of the pattern piece, aimed approximately halfway between the dart point of the bust dart and marked bust apex (line a on diagram below). Beginning a little closer to the CF on the lower curved seam of the Upper Front, draw a line from the edge to the dart point.
b. Line at right angles to CF from the dart end to CF line (line b on diagram).
c. Line through centre of dart to dart point (line c on diagram).
d. Line from dart end to stitch line of armhole seam (line d on diagram).
2. Cut the pattern pieces along these lines, keeping the pivot points intact at dart end and armhole seam (see diagram above for location of pivot points). If you accidentally snip through the pivot point, use some tape to create a hinge.
Be sure to mark the original dart end so you don't lose it in the changes. This is VERY important.
For the following steps, it is a good idea to position your pattern piece over a larger piece of paper, so that once the adjustments are made, you can cut around the entire finished piece. This prevents things from shifting around so much.
3. Secure the top section of the Upper Front pattern piece with tape, then draw a line extending the CF edge below the pattern piece.
Now, apply your full bust difference to the pattern. In our example, the full bust difference is 2" (5cm). Divide the difference in half: for example 2" (5cm) / 2 = 1" (2.5cm) because we are working on half of the front piece.
Slide the side section over by your calculated difference: our example is 1" (2.5cm). Let the dart and armhole of the Upper Front pivot - the side will move down and the dart will open.
You can choose to pivot the Lower Front back down to nothing at the hem at this point if you desire:
4. Slide the centre section down by half the amount the side section slid out in the previous step, so 1/2" (1.25cm), along the CF line you drew earlier.
5. Redraw the dart stitching lines so that they meet at the point of the original dart end.
6. Blend the hem and smooth the armhole if needed.
You may choose to create a cutout in your dart if the dart ends up too wide at the side seam.
7. The adjustment is complete , however, if the location of your Bust Apex is different than the pattern, we'll continue below with a few more steps.
MODIFYING THE BUST APEX
The dart should be positioned so that it points directly towards the Bust Apex. It may be necessary to move the dart up or down so that it is positioned correctly. This adjustment may be all that is needed to improve the fit of a dress with dart shaping.
1. Using just the Upper Front, cut two lines at right angles to the Centre Front Line, above and below the new dart.
2. Slide the darted section down or up by the difference. In the example above, we calculated the difference as 2" (5cm) lower, so we will slide the piece down by that amount.
3. Blend the side seam on both sections.
4. Your pattern piece is now ready to use!
Remember, we always recommend sewing a muslin to test out your pattern adjustment before cutting into your fancy fabric.
Making pattern adjustments may seem a bit daunting at first, but the effort is completely worth it to achieve a beautiful, handmade garment with a custom fit.
If you have any questions about sewing or making adjustments to the Curved Front Plains Dress, please feel free to join us at the Twig + Tale Facebook group.
Read more pattern adjustment tutorials here:
